Company about
Home > How To > Pool Spa Waterfall Not Working

Pool Spa Waterfall Not Working

Contents

Forgot your password? If the light does not come on, check Amp draw on the heater anyway - the light may have gone bad. A stainless steel pressure switch is easier to install with a little PTFE applied to the threads. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! More about the author

If either the = GFI or the circuit breaker continue to trip, check to see you don't have a loose strand of wire grounding out in back of the pump. Step 9 Pump too small - The pump suction cannot overcome the total dynamic head (line resistance) in your pool circulation system. Doing this will give you full access to the forums, where you will be able to receive personalized advice concerning your pool. Also below that is a link pertaining to time clock problems,which can cause the motor not to turn on in the first place.And the last link is for a page with find more info

How To Clean Pool Impeller

If the pool level has not risen, your spa check valve may need to be replaced. This may be in the pond or in any plumbing below the water level. If the plumbing is not too crazy, you may be able to open some unions and then splitting the pump housing to get to the impeller.

  • Other handy links: Support this site, TF Test Kits, Pool School Reply With Quote 05-21-2012,08:44 AM #5 Bama Rambler View Profile View Forum Posts View Articles Mod Squad Join Date
  • Swimming Pool Steve 678 views 6:56 Pentair Intelliflo XF real world on a waterfall - Duration: 3:25.
  • In both cases, a thermostat gives the best performance if the bulb is inside a dry-well (also known as a Thermowell), completely surrounded by the spa water.
  • Electronic Mechanical thermostats have been used on equipment forever.
  • When checking for this voltage, disconnect the wire from the pressure switch so you do not get test interference from voltage that might be coming from the other side of the
  • see impeller cleaning.
  • The pressure seems to be good when the waterfall is shut off, but when you turn it on, the pressure goes to zero.

We will accomplish this by isolating the system into parts. Share your experiences! No debris. Pool Skimmer Not Working Tried to back flush with garden hose but still have the problem.

I just kept at it using the priming plug and filling pump with water. Pool Waterfall Plumbing If you wish to have the low speed remain on, you must either turn the bypass again when it shuts off, or pull the next several trippers to their "ON" position UPDATE: I found this link to the online manual. http://www.inyopools.com/HowToPage/how_to_determine_the_cause_of_low_water_flow_.aspx?CommentPage=1 If it is within one foot of the water level then something is wrong.

If the water level goes down look further at the plumbing. Submersible Pond Pump Troubleshooting Room was very clean and the view was awesome. Help!! TFP Moderator 24' x 52" Round AGP. 2hp/¼hp SPL Power-Flo 2-speed pump. 200sqft Waterway Cartridge Filter. 45MHP2(3GPD) Stenner Peristaltic Pump Pool School ----- Pool Math ----- TF-Test Kit Reply With Quote

Pool Waterfall Plumbing

When mounting a housing to the motor, be sure to center the motor shaft inside the ceramic. see this The impeller should glide on easily and turn onto the shaft easily until the threads bottom out with a very solid stop. How To Clean Pool Impeller Hold it there while an accomplice turns on the hose. Fountain Pump Stopped Working It suggests checking the impeller for debris.

Then check to see if your filter is clogged with debris. I currently own three companies http://www.FrankBowman.com , http://www.SplashPoolsNC.com , http://www.SignatureAquatics.com . The bladder will expand, sealing opening and squirt water back toward the pump. Thermostats - Mechanical vs. How To Prime Pool Pump

It was quiet. Thank you. Inyopools Posted: 04/01/2014 11:30 AM Inyo Product Specialist Jordan - You pool water has something suspended in it that's clogging your filter. http://europrolink.com/how-to/pool-cell-not-working.php Then the pressure inside increases and the water flow into the pool decreases.

I would recommend this hotel. Pool Pump Not Priming I checked and the impeller is not clogged....it runs full speed. Check your pump's impeller - "How To Clean Out a Pool Pump Impeller".

The smaller capacitor is for a 1 HP or smaller motor,the larger capacitor is for a 1.5-2 HP motor Motor Stuck - Hums Then Trips Breaker or Just Shuts Off 1)Most

This would cause the water in the spa to reach temperatures high enough to cause the hi limit switch to trip, disengaging high speed operation (as well as the heater.) If Winterizing plugs are one obvious possibility, though too much debris blocking the inlets or in the pump strainer basket could easily do it as well. 19K gal, vinyl, 1/2 HP WhisperFlo I brushed all 3 and didn't see any debris. How To Backwash A Pool Normal pool operation: POOL MAIN DRAIN open (the amount the pool drain should be open depends on if the pool is equipped with a cleaning system, and what kind), SPA MAIN

Lance Posted: 09/28/2016 19:54 PM I have a aoSmith B748 permanent split cap 2 hp 230vac motor/pump. I try to recirc the filter to prime it but nothing goes to the jets. Make sure there is an adequate amount of DE in DE filters. Room tips (183) 2,198 reviews sorted by: Date | Rating English first French first German first Italian first Portuguese first Russian first Spanish first Swedish first Any English first English first

To determine if the element in a flo-thru is bad, test it the same as you would a regular element. Check the wire powering the air switch and check the switch for continuity. There are two methods of sensing the temperature with these controls. They generally have trimpots inside that are very easily broken.

In many cases, the spa side control sometimes cause nuisance tripping due to water getting inside the socket on the control box. If water is found in the blower line, it may take several hours to dry out. We appreciate your input. Short Filter Runs A build up of dirt and other materials in the filter.

We took the cover off, filled it up to the line with water, and put degreaser in, changed out the sand (21" cooper ranger". Help!! I'm at a loss. WARNING: DO NOT LUBRICATE WITH ANYTHING BUT WATER.

Pump Will Not Come On At All First, determine what voltage the pump you are troubleshooting requires to work. Total Lack of Heat This section applies only to the total lack of heat, not to the lack of enough heat rise. The bypass (if you have one) will only affect operation until a tripper set in a position that will nullify the effect of the bypass function comes in front of the Adjust the wheels to bring the vacuum head off the floor slightly.

Hi ambient temperatures around the pack will effect thermostat calibration. Is the Hi Limit switch tripped? (If so, why?) Are the heater wires burnt? Is there a dedicated pump for the waterfall or does it run off the recirculation pump and just turned on through a valve? The pilot light is out.

My psi is at zero and I prime the pump on recirc.The purpose of the priming plug is to block skimmer while forxing water through the lines out the jets to As for calibrating electronic thermostats, it is usually not possible.