Company about
Home > Power Button > Power Button On Iphone 4s Not Working

Power Button On Iphone 4s Not Working


Conditt, 1h ago save Save share View 1h 9 1h ago in AV Marshall's new headphones let you jam for (at least) 30 hours The on-ear Mid Bluetooth is available now Düşüncelerinizi paylaşmak için oturum açın. NFRDIVR 174.636 görüntüleme 5:52 iPhone 4S Power Button and Proximity Sensors Replacement Disassembly and Reassembly - CRAZYPHONES - Süre: 18:42. jurajtomecek7 - 01/28/2015 Reply I used my 16x magnifier loupe to be certain I had the pressure sensor aligned with the screw hole - no problem, no stripping.

andries - 10/16/2013 Reply This is normal ... I can do it right before I start without much force, is this not better? bluezzer - 10/29/2013 I bent the wire of the silent button on right top of the battery. My refurb'd iPhone 4 had about 15 months of use on it when the power button siezed up (can't push it / doesn't work).I have ordered both a screwdriver set (for Go Here

How To Fix Iphone 4 Power Button Without Taking It Apart

They have quality parts, tools, and much more for all your repair needs. Apple's iPhone 5s and iPhone 5c are the latest models available. I get the vacuum out and go over every inch of the floor to suck up all them screws.

  • Carefully grasp the grounding clip and remove it from the iPhone.
  • Picture two slices of bread but not the same size, stuck together.
  • The cellular antenna connector I pushed down firmly to make sure it was connected, I was gentler the first time, now everything works.

Then, I worked it from the bottom to the top. As noted, the metal lip below the (red) 2.7mm screw and to the right of the (green) 1.2mm screw goes between the ribbon cable and the main logic board. After removing it you'll also notice a gold grounding clip underneath it. Iphone 6 Lock Button Stuck Down Major advice is to be patient.

No real issues. Iphone 4s Power Button Replacement Floris Jansen - 01/21/2014 Reply I agree. Temp sensor is on the battery and returning to old battery fixed it. I skipped steps 20 and 21 as it is not necessary to remove the front facing camera for this repair.

I bought a ph000 screwdriver off the internet. Iphone 6 Power Button Stuck Reg: Out of Stock Ready to Ship 1 1 2 3 4 5 more-horizontal_small checkmark_small times_small Add to Cart Ready to Ship Notify me Out of Stock Out of Stock Ready In Step 8 I think the colors of the screws are inverted. Unfortunately, this is one of the last components to be removed from the iPhone during repair, so you'll need to do a lot of fiddly work before you get to it.

Iphone 4s Power Button Replacement

I tried and failef to fix it, and had to replace the phone. Now what? How To Fix Iphone 4 Power Button Without Taking It Apart When I was removing the camera module, accidently removed small element, which is marked with the red line Iphone 6 Lock Button Stuck One of the cables lies underneath the bottom most cable so you'll need to disconnect the cable over it before folding it back and revealing the shorter cable underneath.

Tool ticklejahfancy - 05/09/2015 my screws are stipped and i am going though the front glass to get to the logic board could some one give me a guide on how useful reference jfksdca - 05/23/2014 Reply I didn't find any need to remove the pressure contact. The work around doesn't allow for screenshots and is inconvenient to say the least. Are you kidding me!! Iphone Power Button Not Working How To Turn On

Find out how to unlock your iPhone 4 here. iPhoneRepairMia 1.231.133 görüntüleme 8:32 iPhone 4 Power Button Repair NOT Replacement Guide Tutorial - - Süre: 17:24. Remove the rear camera from the iPhone. The home screen!.

On 25 April 2014, the company confirmed that some iPhone 5 smartphones have defective power buttons and has offered a free replacement. “Apple has determined that the sleep/wake button mechanism on Iphone 6 Power Button Stuck Down Finally, I completed driving the lower screw. I twisted and pulled.

just keep them all separate.

I just used this guide (in conjunction with a very reasonable $20 part from eBay) to fix up my 4s! Please type your message and try again.            CwissyBwear Level 1 (0 points) Q: iPhone 4 Power Button Stuck Out of the blue today the power/lock button on my iPhone If I hear back from them and they want me to pay, no matter how much, I'm gonna get furious and I wont pay a dime.Gah, Aug 3, 2012 10:57 AM Iphone 6 Power Button Not Working Do not attempt to completely remove it yet as it's still attached.You may choose to remove the actual power button if you'd like but it's not necessary.

Lars - 07/10/2015 Reply There's only one Philips screwdriver with the kit but it failed to unscrew the top 1.7mm one off the connector unfortunately. Replacement power button flex cable - Buy now 5-point security screwdriver - Buy now Standard #000 Phillips screwdriver - Buy now Spudger tool - Buy now Razor blade - Buy Now Got a big scare as the phone would not connect to the cell network at first boot, only WiFi. get redirected here Note that the reassembly is everything from the screen back to completely reassembled.

Please help!! When I got to the power/ . . . It fell off and I couldn't see where to to fit it back. It fell off during removal and I cant seem to locate it in the pictures. :( Shaun Brown - 06/30/2015 As noted: Put the bumper back right above the white bar

My Advice Pay someone that knows what they are doing... Ian Epperson - January 5 Reply Same here.. Triple-click again and it'll reappear. spoke too soon, i 'spect...random reboots persist.

Sometimes it will randomly turn on or awaken after I've pressed these butons several times. No way a rear panel replacement would take 2 hours - can be done in 2 minutes! I skipped steps 20 and 21 as it is not necessary to remove the front facing camera for this repair. Typically issues would begin when users noticed that they'd have to push down on one specific side of the power button or their iPhone 5 would not lock.

You might need to slightly bend the contact in step 5 up just a little, so it will make contact with the metal back plate. The bumper goes on the edge of the board to protect the ribbon cables that bend over the board. Needed to use a tweezer on the pressure contact on the top screw of the battery.