Company about
Home > Power Button > Power Button On Itouch 4 Not Working

Power Button On Itouch 4 Not Working


Not as easily, but still very doable, snake the new battery ribbon back through the same slot; solder 3 points and reassemble. Loading... COMO REPARAR EL BOTON POWER (PART 2) - Duration: 13:33. HBT 35,642 views 3:02 iPod 4G flex removals - Duration: 5:36. navigate to this website

Much simpler, and didn't cause any problems -- the mid plane didn't deform, and snapped right back into place. This feature is not available right now. Be very careful not to lift too much as the volume control ribbon cable is still connected and will tear very easily. Do not apply too much solder.

Ipod Touch 4th Generation Power Button Stuck

Will this be because I can't get one on here? So It looks like battery is OK. will they fix the power button for me if i pop in to the apple store after school? Pry upward to separate the plate from the adhesive securing it to the plastic inner case.

Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. Close Yeah, keep it Undo Close This video is unavailable. LCD and Digitizer worked. Ipod Touch 4th Generation Power Button Repair hutchwilco - 01/25/2014 Reply Add a comment Add Comment 1024 Step 13 Edit Use the edge of an iPod opening tool to gently pry, but not remove, the rear-facing camera away

the power switch and the volume up/down are all one very frail wire harness that is frequently severed when a novice tries to replace a broken upper glass (screen). Sign in to report inappropriate content. COMO REPARAR EL BOTON POWER. (PART 1) iDlorepair - DLO SubscribeSubscribedUnsubscribe6,0776K Loading...! I only speak of myself because I have put together again a 4g Touch and it was totally unresponsive.

Add to Want to watch this again later? Ipod Touch 4th Generation Lock Button Stuck Without the copper tape it should work anyway but I would just lift up and move one part of the tape so that it is in contact with the other part Fboecom - September 4 Reply Add a comment Add Comment 1024 Step 20 Volume/Power Button Cable Edit Remove the two 1.3 mm Phillips #00 screws securing the Volume/Power button cable metal DO NOT bridge the connection between the solder pads both on the board and on the ribbon cable with your spudger.

  1. Was this answer helpful?
  2. The ipod I have was given to me with much of the glass smashed and picked out, so some of this is just missing.
  3. If parts are actually needed because it's the rare case of a failed switch not a slipped disc, I gift the part into the repair.
  4. View the answer I have this problem too Subscribed to new answers Is this a good question?
  5. iPhoneTechLab 188,887 views 4:50 Power Button & Proximity Repair - iPhone 4 How to Tutorial - Duration: 8:32.
  6. If you push the button and then push device it will have a "lock" option that will function exactly like your power button.
  7. COMO REPARAR EL BOTON POWER (PART 2) - Duration: 13:33.
  8. Hello all, I've been using iFixIt for a few weeks now and have learned a lot already.
  9. Katie Kousoulos - 08/23/2013 Reply after removed the steel mid plate, does anybody measure the battery voltage?

Ipod Touch Power Button Not Working

DirectFix 126,311 views 8:52 How to Repair a 4th Generation iPod Touch - Duration: 7:51.

Rating is available when the video has been rented. Ipod Touch 4th Generation Power Button Stuck This makes things much simpler for subsequent steps rather than having the front panel dangling there. Ipod Nano Power Button Not Working Sign in to make your opinion count.

Use your plastic pry tool and make sure the flex cable, between the board and power button is not on top of the board. useful reference jimmy - 08/04/2012 Reply Thats really bad all you have to do is buy some and replase it ben folks - 02/26/2015 Search at ebay Haris Kyritsis - 01/15/2015 Reply Add If the adhesive is too difficult to separate, use a heat gun to soften it before proceeding. Watch Queue Queue __count__/__total__ Find out whyClose Fixing power and volume buttons in 4th gen iPod Touch Leon Stacey SubscribeSubscribedUnsubscribe11,22411K Loading... Ipod Touch Power Button Not Working How To Turn Off

Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Sign in to make your opinion count. Sign in to add this video to a playlist. my review here I haven't got any more warrenty since the start of 2013.

Also what goes first in the process when doing both of those things ? Ipod Touch 2g Power Button Not Working The digitizer cable was too fragile, and cracked. Category People & Blogs License Standard YouTube License Show more Show less Loading...

COMO REPARAR EL BOTON POWER. (PART 1) - Duration: 13:42.

ThirdHand TV 336,117 views 2:40 How to fix Iphone power button for FREE - Duration: 3:16. In fact, I have seen people remove it completely. I found the power source dropped to only 1.65V and 50mA. Ipod Touch Lock Button Stuck Go Cell Phone Repair 528,041 views 44:43 iPOD TOUCH 4G, HOW TO FIX POWER & HOME BUTTON.

Syl2us - 06/17/2013 Reply I stopped dismantling here as well and was able to replace the battery and everything works on the ipod. Pry the bottom edge of the front panel upward, being careful not to bend the glass excessively. Touch2GenIpod 852,530 views 3:50 iPod Touch 1st Generation Repair Take Apart Video - Duration: 10:50. In fact I used contact spray directly into the volume button.

I wonder if the button has been moved out of place when I replaced the screen? vgcrepairs 8,718 views 5:36 iPOD TOUCH 4G, HOW TO FIX POWER & HOME BUTTON. Reassembly was tough because I didn't have the ipod dock connector seated correctly, AND more importantly, the speaker has a part that needs to be inserted into a black part on the 4g Touch is extremely sensitive in that area and the first time I opened a 4g Touch I tore that cable because it sticks to the mid plane.You see it

I just have the Auto-Lock set for 1 minute, so it does go to sleep, or is at least inactive when the Wi-fi is off. It lifted up enough from the iPod's body that I was able to slip the ribbon in around the support it sticks to and hold it in place until the adhesive Sign in to add this video to a playlist.